Contents
-. Build : WizFi630A 개발환경 구축
-. Upgrade : TFTP 활용
Upgrade : TFTP 활용
WizFi630A in OpenWrt
>> 참조 링크
https://wiki.openwrt.org/toh/wiznet/wiznet_wizfi630a
>> tftp 설치
>> /etc/xinetd.d/tftp 파일 생성 및 수정
>> tftp root 디렉토리 생성 및 서비스 실행
>> Upgrade binary 복사
>> Upgrade log
U-Boot 1.1.3 (Mar 1 2016 - 13:35:45)
Board: Ralink APSoC DRAM:
Return Real size =33554432 !!
32 MB
relocate_code Pointer at: 81fb4000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 21
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
raspi_read: from:30000 len:1000
.raspi_read: from:30000 len:1000
.============================================
Ralink UBoot Version: 3.5.0.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Mar 1 2016 Time:13:35:45
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2 <<= 2번선택
0
raspi_read: from:40028 len:6
.
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) ==:192.168.0.20 <<= 임의 IP 할당
Input server IP (10.10.10.3) ==:192.168.0.2 <<= tftp서버 IP 입력
Input Linux Kernel filename () ==:wizfi630a.bin <<= 복사된 binary 파일명 입력
netboot_common, argc= 3
NetTxPacket = 0x81FE5F40
KSEG1ADDR(NetTxPacket) = 0xA1FE5F40
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.0.2; our IP address is 192.168.0.20
Filename 'wizfi630a.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
T T T T Got ARP REPLY, set server/gtwy eth addr (bc:5f:f4:da:9c:bb)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################
done
Bytes transferred = 4194308 (400004 hex)
NetBootFileXferSize= 00400004
raspi_erase_write: offs:50000, count:400004
raspi_erase: offs:50000 len:400000
................................................................
raspi_write: to:50000 len:400000
................................................................
raspi_read: from:50000 len:10000
.raspi_read: from:60000 len:10000
.raspi_read: from:70000 len:10000
.raspi_read: from:80000 len:10000
.raspi_read: from:90000 len:10000
.raspi_read: from:a0000 len:10000
.raspi_read: from:b0000 len:10000
.raspi_read: from:c0000 len:10000
.raspi_read: from:d0000 len:10000
.raspi_read: from:e0000 len:10000
.raspi_read: from:f0000 len:10000
.raspi_read: from:100000 len:10000
.raspi_read: from:110000 len:10000
.raspi_read: from:120000 len:10000
.raspi_read: from:130000 len:10000
.raspi_read: from:140000 len:10000
.raspi_read: from:150000 len:10000
.raspi_read: from:160000 len:10000
.raspi_read: from:170000 len:10000
.raspi_read: from:180000 len:10000
.raspi_read: from:190000 len:10000
.raspi_read: from:1a0000 len:10000
.raspi_read: from:1b0000 len:10000
.raspi_read: from:1c0000 len:10000
.raspi_read: from:1d0000 len:10000
.raspi_read: from:1e0000 len:10000
.raspi_read: from:1f0000 len:10000
.raspi_read: from:200000 len:10000
.raspi_read: from:210000 len:10000
.raspi_read: from:220000 len:10000
.raspi_read: from:230000 len:10000
.raspi_read: from:240000 len:10000
.raspi_read: from:250000 len:10000
.raspi_read: from:260000 len:10000
.raspi_read: from:270000 len:10000
.raspi_read: from:280000 len:10000
.raspi_read: from:290000 len:10000
.raspi_read: from:2a0000 len:10000
.raspi_read: from:2b0000 len:10000
.raspi_read: from:2c0000 len:10000
.raspi_read: from:2d0000 len:10000
.raspi_read: from:2e0000 len:10000
.raspi_read: from:2f0000 len:10000
.raspi_read: from:300000 len:10000
.raspi_read: from:310000 len:10000
.raspi_read: from:320000 len:10000
.raspi_read: from:330000 len:10000
.raspi_read: from:340000 len:10000
.raspi_read: from:350000 len:10000
.raspi_read: from:360000 len:10000
.raspi_read: from:370000 len:10000
.raspi_read: from:380000 len:10000
.raspi_read: from:390000 len:10000
.raspi_read: from:3a0000 len:10000
.raspi_read: from:3b0000 len:10000
.raspi_read: from:3c0000 len:10000
.raspi_read: from:3d0000 len:10000
.raspi_read: from:3e0000 len:10000
.raspi_read: from:3f0000 len:10000
.raspi_read: from:400000 len:10000
.raspi_read: from:410000 len:10000
.raspi_read: from:420000 len:10000
.raspi_read: from:430000 len:10000
.raspi_read: from:440000 len:10000
.raspi_read: from:450000 len:10000
.raspi_erase: offs:450000 len:10000
.
raspi_write: to:450000 len:10000
.
raspi_read: from:450000 len:10000
.Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: MIPS OpenWrt Linux-4.4.14
Created: 2017-05-24 14:54:37 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1216606 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:12905e
................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
linux_argv[0] = <NULL>
linux_env = �7�����7��7��7��7�
Starting kernel ...
[ 0.000000] Linux version 4.4.14 (bingdo@bingdo-desktop) (gcc version 5.3.0 7
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is WIZnet WizFi630A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bys
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa8
[ 0.000000] Kernel command line: console=ttyS1,115200 rootfstype=squashfs,jf2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00001fd0
[ 0.000000] Readback ErrCtl register=00001fd0
[ 0.000000] Memory: 28488K/32768K available (2751K kernel code, 125K rwdata,)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_s
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_s
[ 0.000016] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 1193s
[ 0.007697] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.080250] pid_max: default: 32768 minimum: 301
[ 0.084964] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091394] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.107822] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.117766] pinctrl core: initialized pinctrl subsystem
[ 0.124158] NET: Registered protocol family 16
[ 0.172470] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.177905] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.184411] rt2880_gpio 10000660.gpio: registering 6 gpios
[ 0.189744] rt2880_gpio 10000660.gpio: registering 6 irq handlers
[ 0.198693] clocksource: Switched to clocksource MIPS
[ 0.206356] NET: Registered protocol family 2
[ 0.212343] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.219234] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.225384] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.231857] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.237520] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.244274] NET: Registered protocol family 1
[ 0.249568] rt-timer 10000100.timer: maximum frequency is 3662Hz
[ 0.257280] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.308059] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.313856] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[ 0.330225] io scheduler noop registered
[ 0.334010] io scheduler deadline registered (default)
[ 0.339600] ralink-usb-phy usbphy: invalid resource
[ 0.345128] gpio-export gpio-export: 0 gpio(s) exported
[ 0.350846] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.359634] 10000500.uart: ttyS0 at MMIO 0x10000500 (irq = 13, base_baud = 23
[ 0.370336] console [ttyS1] disabled
[ 0.373835] 10000c00.uartlite: ttyS1 at MMIO 0x10000c00 (irq = 20, base_baud3
[ 0.383580] console [ttyS1] enabled
[ 0.383580] console [ttyS1] enabled
[ 0.390681] bootconsole [early0] disabled
[ 0.390681] bootconsole [early0] disabled
[ 0.409919] spi spi0.0: force spi mode3
[ 0.414730] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.419732] 4 ofpart partitions found on MTD device spi0.0
[ 0.425341] Creating 4 MTD partitions on "spi0.0":
[ 0.430301] 0x000000000000-0x000000030000 : "uboot"
[ 0.439213] 0x000000030000-0x000000040000 : "uboot-env"
[ 0.448455] 0x000000040000-0x000000050000 : "factory"
[ 0.457685] 0x000000050000-0x000001000000 : "firmware"
[ 0.544317] 2 uimage-fw partitions found on MTD device firmware
[ 0.550504] 0x000000050000-0x00000017909e : "kernel"
[ 0.559061] 0x00000017909e-0x000001000000 : "rootfs"
[ 0.568034] mtd: device 5 (rootfs) set to be root filesystem
[ 0.574143] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580560] 0x000000440000-0x000001000000 : "rootfs_data"
[ 0.595952] rt3050-esw 10110000.esw: link changed 0x00
[ 0.605040] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb5
[ 0.614744] rt2880_wdt 10000120.watchdog: Initialized
[ 0.622927] NET: Registered protocol family 10
[ 0.635855] NET: Registered protocol family 17
[ 0.640790] bridge: automatic filtering via arp/ip/ip6tables has been deprec.
[ 0.653831] 8021q: 802.1Q VLAN Support v1.8
[ 0.676668] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.685944] Freeing unused kernel memory: 180K (80373000 - 803a0000)
[ 3.086112] init: Console is alive
[ 3.090385] init: - watchdog -
[ 5.267686] usbcore: registered new interface driver usbfs
[ 5.273678] usbcore: registered new interface driver hub
[ 5.279483] usbcore: registered new device driver usb
[ 5.296553] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.306132] ehci-platform: EHCI generic platform driver
[ 5.322256] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.328333] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.332995] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.339032] ehci-platform 101c0000.ehci: new USB bus registered, assigned bu1
[ 5.347391] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.368833] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.377718] hub 1-0:1.0: USB hub found
[ 5.382540] hub 1-0:1.0: 1 port detected
[ 5.397544] init: - preinit -
[ 6.496392] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.827233] random: procd urandom read with 11 bits of entropy available
[ 8.136889] rt3050-esw 10110000.esw: link changed 0x02
[ 10.217278] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 10.275670] procd: - early -
[ 10.279068] procd: - watchdog -
[ 11.380848] procd: - ubus -
[ 11.440191] procd: - init -
Please press Enter to activate this console.
[ 12.710961] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.744086] Loading modules backported from Linux version wt-2016-05-12-0-g76
[ 12.751976] Backport generated by backports.git backports-20160216-0-ge3c56e4
[ 12.767462] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.792994] nf_conntrack version 0.5.0 (447 buckets, 1788 max)
[ 12.869623] xt_time: kernel timezone is -0000
[ 12.982450] PPP generic driver version 2.4.2
[ 12.993168] NET: Registered protocol family 24
[ 13.050600] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 d
[ 13.058559] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 21.372585] rt3050-esw 10110000.esw: link changed 0x00
[ 22.989706] rt3050-esw 10110000.esw: link changed 0x02
[ 31.880146] device eth0.1 entered promiscuous mode
[ 31.885078] device eth0 entered promiscuous mode
[ 31.921814] br-lan: port 1(eth0.1) entered forwarding state
[ 31.927623] br-lan: port 1(eth0.1) entered forwarding state
[ 33.918775] br-lan: port 1(eth0.1) entered forwarding state
[ 58.161822] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 58.179218] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 58.186007] jffs2_build_filesystem(): erasing all blocks after the end marke
[ 79.588798] random: nonblocking pool is initialized
'오픈소스 HW > WIZnet' 카테고리의 다른 글
| WIZnet W5500+ESP32 SDK를 이용한 IoT Gateway 만들기 프롤로그 (0) | 2021.07.06 |
|---|---|
| WIZnet WizFi630A HOWTO - Build (0) | 2017.06.01 |
| How to porting WIZInterface library into mbed OS5 temporarily (0) | 2016.12.23 |
| TFTP Example on WIZwiki-W7500 platform (0) | 2015.10.14 |
| Convert ioLibrary into BSD socket style on WIZwki-W7500 platform (0) | 2015.10.06 |